UNIVERSAL
WINDAGE TRAYS |
 CANTON’S Universal
Screen Windage Trays deliver the maximum oil control and horsepower savings.
These trays use one-way screen which follows the radius of the crankshaft.
This design allows oil coming off the crank to pass thru the screen and not
allow the oil in the sump to reach the rotating assembly. |
|
#20-906 This one-way screen windage kit can be
used in almost any application. Includes a 22" x 12" sheet of one-way screen,
two 1" x 1/8" x 24" mounting rails and all necessary clips, washers and locking
screws needed. Welding is required. |
back to top |
|
|
CHEVY WINDAGE TRAYS |
|
CHEVY PRO PLUS
WINDAGE TRAYS |
 The
SBC Pro-Plus windage tray is mounted
off of the main caps and is designed as an integral part of the Pro-Plus oil recovery
system. Mounting the tray off of the main caps seals the pickup area off from the
crank windage and keeps oil from splashing out of that area under race conditions.
#20-908 S.B. Chevy Pro Plus windage tray
#20-908S S.B. Chevy Pro Plus windage tray - short style
#20-909 B.B. Chevy Pro Plus windage tray
| |
Recommended Mounting Studs.
#20-921 for SBC
#20-927 for BBC |
back to top |
|
|
CHEVY SCREEN
WINDAGE TRAYS |
 Our Chevy Main
Cap Mounted Screen
Windage Trays come in short and full length versions. The short style tray
fit into stock or aftermarket oil pans with stock front sections and the
full length trays only fit into aftermarket oil pans that are deeper
in the front. |
|
#20-910 SBC short style Screen Windage
trays for left side dipsticks.
#20-910T SBC short style Screen Windage trays for right side dipsticks.
#20-911 SBC full length Screen Windage trays for left side dipsticks.
#20-911T SBC full length Screen Windage trays for right side dipsticks.
#20-916 BBC short style Screen Windage trays.
#20-917 BBC long style Screen Windage trays.
Recommended Mounting Studs.
#20-920 for SBC.
#20-926 for BBC. |
back to top |
|
|
CHEVY WINDAGE
TRAYS MOUNTING KITS |
 #20-920 SBC
Mounting kit for Screen Windage Trays (3 studs, nuts and washers).
#20-921 SBC Mounting kit for Pro-Plus Windage Trays (#20-908).
#20-926 BBC Mounting kit for Screen Windage Trays
(4 studs, nuts and washers). |
back to top |
|
|
PONTIAC WINDAGE TRAYS |
|
PONTIAC WINDAGE
TRAY |
 #20-918 The Pontiac Screen
Windage Tray sandwiches
between block and the pan. Made to be used with the 301-455 blocks and aftermarket
pans that are deeper in the front than OE.
The half-screen, half-solid design
offers superior oil control and horsepower savings when compared to previous
designs. This full-length tray wraps around the oil pump and provides windage
control for the entire rotating assembly. The rail mounted design eliminates
the need for mounting studs and allows installation on engines not originally
equipped with stock trays.
|
back to top |
|
PONTIAC PRO STYLE WINDAGE
TRAY |
 #20-918P The Pontiac Pro style
Windage Tray sandwiches
between block and the pan. Made to be used with the 301-455 blocks and aftermarket
pans that are deeper in the front than OEM.
The solid louver design offers superior oil control and horsepower savings. This full length tray wraps around the oil pump and provides windage control for the entire rotating assembly. For ease of installation, use our # 22-310 oil pan stud kit.
|
back to top |
|
|
FORD WINDAGE TRAYS |
|
289,302,351C/M,351W
AND 429/460
FORD SCREEN WINDAGE TRAYS |
 |
#20-930 289-302 Ford Screen Windage trays
for rear sump.
Note: 94-95 stock Mustang style oil pan is a tight fit.
#20-931 289-302 Ford Screen Windage trays for front sump.
#20-932 351w Ford Screen Windage trays for rear sump.
#20-933 351w Ford Screen Windage trays for front sump.
#20-934 351c Ford Screen Windage trays for rear sump.
#20-935 351c Ford Screen Windage trays for front sump.
#20-936 429-460 Ford Screen Windage trays for front
and rear sump. |
|
These trays are
designed to fit into stock
and aftermarket oil pans.
Mounting hardware necessary for installation is listed below. |
back to top |
|
289,302,351W
FORD PRO STYLE LOUVERD WINDAGE TRAYS |
 |
(20-931P Shown in photo)
#20-930P 289-302 Ford Pro Louverd Windage trays
for rear sump.
Note: 94-95 stock Mustang style oil pan is a tight fit.
#20-931P 289-302 Ford Pro Louverd Windage trays for front sump.
#20-932P 351w Ford Pro Louverd Windage trays for rear sump.
#20-933P 351w Ford Pro Louverd Windage trays for front sump.
|
|
These trays are
designed to fit into stock
and aftermarket oil pans.
Mounting hardware necessary for installation is listed below. |
back to top |
|
|
289,302,351C/M,351W
AND 429/460
FORD WINDAGE TRAYS MOUNTING AND MAIN CAP STUD KITS |
 |
#20-940 289-302 Windage tray mounting kit.
#20-941 289-302 Full main cap stud kit for use with our Windage Tray.
Note: For R302 Engine Blocks use #20-942 or #20-943.
#20-942 351w / 351c Windage tray mounting kit.
#20-943 351w / 351c Full main cap stud kit for use with our Windage Tray.
#20-946 429-460 Windage tray mounting kit.
-The 429-460 mounting
kit includes bolts, not studs.
-Please call if you have questions. |
|
Mounting Kits include four main cap studs, nuts,
washers and tray mounting hardware.
Full main cap mounting kits include ten main cap studs, nuts, washers
and accessory mounting hardware. |
back to top |
|
|
4.6 / 5.4 FORD
WINDAGE TRAYS KITS |
 |
#20-939 4.6 Ford Screen Windage
tray for stock or aftermarket oil pans. Mounts between the oil pan
and block, includes oil pan studs and nuts.
Recommended or related parts.
#88-780 Oil pan gasket for 4.6 and 5.4 Ford. |
back to top |
|
|
FE FORD WINDAGE TRAYS |
 |
#20-938 428 FE Ford Screen Windage trays
for stock or aftermarket front sump oil pans. Mounts between the oil pan and
block and includes oil pan studs and nuts.
Recommended or related parts.
#88-800C Oil pan gasket for Ford FE. |
back to top |
|
|
HONDA B-SERIES WINDAGE TRAY |
 |
#20-912 Mutli-louvered windage tray designed to mount between
a non-girdle engine block and canton oil pan #15-962 to maximize horsepower.
Includes oil pan mounting studs and nuts
|
back to top |
|
|
WINDAGE
TRAYS FOR MAIN SUPPORT |
|
WINDAGE TRAYS FOR
MAIN SUPPORTS |
 These Main Support Windage
Trays bolt to the pre-drilled and tapped holes on our main cap
stud supports. These trays keep the windage around the rotating
assembly away from the oil in the sump and the oil in the sump away
from the rotating assembly. Come with mounting bolts. |
|
#20-960 Ford 289-302 Main Cap Stud Support Windage Tray.
#20-962 Ford 351W Main Cap Stud Support Windage Tray.
#20-966 Ford 429-460 Main Cap Stud Support Windage Tray. |
back to top |
|
|
|
|
